Add WIA Drivers

Before proceeding, ensure that the latest version of your job file is saved to Dynalite Cloud.

Dynalite Enabler App

Dynalite Enabler connects to wireless drivers over Bluetooth, configures them for the PDZG-E’s Zigbee network key, and assigns each driver to your chosen area/channel/BLA in the SB job file via Dynalite Cloud.

The Enabler app requires an internet connection to access Dynalite Cloud. If there is no internet connection available in the building, you can launch the app and open the project before losing reception. Go inside and commission the project, and then synchronise the data when your device is back online.
Always make sure to synchronise the data of the commissioned project. Don’t uninstall the app or change the project as this will prevent synchronisation.

Open Cloud Project

App login:

  1. Open the app on your device. On the first login, you will be prompted to agree with the Terms of Software Service.

  2. Select your region: Global

  3. Select the system you want to commission: Dynalite

  4. Enter your username (email address) and tap Next.

  5. Enter your password and tap Sign in.

pde select region
pde select system dynalite
Set up internet connectivity:

  1. Log in to the app and select the project to commission.

  2. Tap Establish connectivity, then Use available internet connection.

  3. The system checks the internet connection.

  4. Tap Done.

pde login
pde projects
pde connectivity setup

Add and Test Drivers

Add lights:

  1. In the app, tap Area commissioning.

  2. Select an Area and a Channel to commission.

    • Don’t use the Unassigned Area for commissioning.

    • If the app asks permission to use Bluetooth, tap Allow.

  3. Tap Add lights.

  4. Under Wireless networks, select the required PDZG-E and tap Select.
    The app performs a Bluetooth scan and lists all discovered drivers.

  5. Identify each driver by tapping its de icon driver icon to blink the light.

  6. If the blinked light belongs to the current channel, tap Add. Repeat for all lights in the channel.

  7. Test the channel (if required) or tap Done to finish.

pde area channels
pde select wireless network
pde add lights
Test channel:

  1. After adding lights to a channel, tap Test channel.
    An ON/OFF button appears, showing the current state of the channel’s lights.

  2. Wait a few seconds for the button to become responsive, then tap it to turn the channel lights on and off.

  3. Confirm that all drivers assigned to the channel respond correctly, then tap Done.

    pde test channel
Test area:

  1. After finishing all channels in an area, select the area and tap Test area.

  2. As before, use the ON/OFF button to test all channels in the area.

  3. After confirming that all channels in the area respond as expected, tap Next.

  4. Select the status of the area and add a note if required.

  5. Tap Done to finish.

pde area status
pde area note

Reassign Drivers to a New Network

If a driver is already assigned to the wrong wireless network, follow the steps below to reset and reassign it.

Reset lights:

  1. In case not all lights can be found, tap I cannot find all lights.

  2. Follow the prompts and tap Retry.

  3. If the problem persists, tap I cannot find all lights and then I still cannot find all lights.

  4. Tap the driver’s de icon driver icon to blink the light. When you find a light that belongs to the channel that you are editing, tap Reset.

  5. Add the light to the channel following the previous procedure.

    pde reset lights

System Builder

You can now open the updated job file in System Builder by clilcking File > Open… sb icon dynalite cloud Open Job From Cloud… (Ctrl+Shift+O)

See Dynalite Cloud > Opening a Job from the Cloud for more information.

Save Wireless Drivers from Dynalite Cloud to PDZG-E

Update PDZG-E:

  1. In System view, select the PDZG-E and sb icon save to device Save modified device data to the device ( Shift+F12 ).

  2. Wait for the PDZG-E to update and reset, then click sb icon send device sign on Send Device Sign-On ( F6 ) to confirm that it is connected and operational.

After saving device data, the PDZG-E automatically writes any required scene/group updates to associated Zigbee devices. Due to Zigbee’s bandwidth limitations, this can take more than 10-20 minutes to complete.

You will not be able to open the Zigbee network to add autojoin devices until the process is complete. You can monitor the progress % in the Network Log.

sb network log writing zigbee scenes