Button Functions and Sub functions
The following functions are available for each button. Each function may have one or more sub functions and settings:
Advanced Channel Level Custom Room Status Hospitality applications only, see Architecture STR documentation on the Signify MyLighting Portal. |
One Touch Preset Ramp Task No function |
Additional page navigation functions are available on the AntumbraDisplay:
Goto Page |
Temperature Setpoint |
Advanced
Sign On
This diagnostic function checks the button by sending a DyNet sign-on message to the network.
Event Control
Remotely triggers an event on a different device on the network.
| Property | Description |
|---|---|
Control type |
Enable, Disable, or Trigger an event when the button is pressed. |
Device Code |
Identifies the target device type. |
Box number |
Identifies the target device. |
Event number |
Identifies the event on the target device. |
Panic
| Property | Description |
|---|---|
Panic |
If True, sets the selected area to panic mode when the button is pressed, raising all dimming levels to 100% and locking UI controls for that area. |
Fade time |
The time taken for dimming levels to fade from their current setting to 100%. |
Panel enable / disable
| Property | Description |
|---|---|
Enable Panel |
Enables (True) or disables (False) the keypad. |
DyNet mute |
Stop DyNet messages being created by this function. |
Set Join level
Dynamically modifies the native join of UIs/sensors in an area. The Logical Address > Area/Join button properties determine which devices in which area are affected.
| Property | Description |
|---|---|
Join Level |
Targeted devices in the specified area are set to this native join value (0-255) when the button is pressed. |
DyNet mute |
Stop DyNet messages being created by this function. |
DyNet1 logical messages
This advanced function sends a customized DyNet logical message over the network.
We strongly recommend consulting with Philips Dynalite before attempting to use this.
| Property | Description |
|---|---|
Opcode |
Opcode of the logical message |
Data1 |
First data byte |
Data2 |
Second data byte |
Data3 |
Third data byte |
DyNet1 physical message
This advanced function sends a customized DyNet physical message over the network.
We strongly recommend consulting with Philips Dynalite before attempting to use this.
| Property | Description |
|---|---|
Device Code |
Identifies the target device type. |
Box Number |
Identifies the target device. |
Opcode |
Opcode of the physical message |
Data1 |
First data byte |
Data2 |
Second data byte |
Data3 |
Third data byte |
Channel Level
Channel Level
| Property | Description |
|---|---|
Level (%) |
Sets the channel level (brightness) |
Fade (rounded to 10 ms) |
The time taken to fade to the requested channel level |
Off preset |
Defines the off preset number for the area. If this preset is recalled, the button’s indicator LED will deactivate. |
DyNet mute |
Stop DyNet messages being created by this function. |
Color Temperature
This function sets the channel level and colour temperature for compatible tunable white luminaires.
| Property | Description |
|---|---|
Color temperature (Kelvin) |
Sets the colour temperature. |
Set colour temperature only |
If True, Level (%) is ignored |
Level (%) |
Sets the channel level (brightness) |
Fade (rounded to 10 ms) |
The time taken to fade to the requested channel level |
Off preset |
Defines the off preset number for the area. If this preset is recalled, the button’s indicator LED will deactivate. |
DyNet mute |
Stop DyNet messages being created by this function. |
On channels only |
If True, message is ignored by channels that are off or at 0% |
Increment Channel Level Step
This function increases the channel level by the specified amount within a defined range.
| Property | Description |
|---|---|
Start Level |
Sets the lowest light level on the channel (0-255) |
End Level |
Sets the highest light level on the channel (0-255) |
Step |
The step size for each increment (default: 5) |
Fade (rounded to 10 ms) |
The time taken to fade to the requested channel level |
DyNet mute |
Stop DyNet messages being created by this function |
Decrement Channel Level Step
This function decreases the channel level by the specified amount within a defined range.
| Property | Description |
|---|---|
Start Level |
Sets the highest light level on the channel (0-255) |
End Level |
Sets the lowest light level on the channel (0-255) |
Step |
The step size for each decrement (default: 5) |
Fade (rounded to 10 ms) |
The time taken to fade to the requested channel level |
DyNet mute |
Stop DyNet messages being created by this function |
Custom
Custom
This function uses advanced custom actions built using the Action Chain Editor.
Refer to the System Builder Training Guide for more information.
| Property | Description |
|---|---|
Press actions |
Selects the actions to execute on each type of button event. |
Release actions |
|
Extended press actions |
|
Extended release actions |
One Touch
Toggle Preset
| Property | Description |
|---|---|
On Preset |
Defines the preset for the button’s ON state. |
Off Preset |
Defines the preset for the button’s OFF state. |
Fade (rounded to 10 ms) |
Time taken to transition between presets. |
DyNet Mute |
Stops DyNet messages being created by this function. |
One touch with ramp
| Property | Description |
|---|---|
On Preset |
Defines the preset for the button’s ON state. |
Off Preset |
Defines the preset for the button’s OFF state. |
Fade (rounded to 10 ms) |
Time taken to reach the preset level if the button is tapped. |
Ramp rate (rounded to 10 ms) |
Time taken to ramp up to the required level if the button is held. |
Min ramp level (%) |
Minimum light level when ramping down. |
DyNet Mute |
Stops DyNet messages being created by this function. |
Double send stop fade |
If True, 'stop fade' command is sent twice to compensate for busy networks. |
One touch ramp with program
| Property | Description |
|---|---|
On Preset |
Defines the preset for the button’s ON state. |
Off Preset |
Defines the preset for the button’s OFF state. |
Fade (rounded to 10 ms) |
Time taken to reach the preset level if the button is tapped. |
Ramp rate (rounded to 10 ms) |
Time taken to ramp up to 100% if the button is held. When the button is released, the current level is saved to the On Preset. |
Min ramp Level (%) |
Minimum light level when ramping down. |
DyNet Mute |
Stops DyNet messages being created by this function. |
Single direction one touch
| Property | Description |
|---|---|
Preset |
Defines the preset recalled by a short button press |
Level (%) |
Defines the channel level to ramp towards when the button is held. |
Fade (rounded to 10 ms) |
Time taken to reach the preset level if the button is tapped, or channel level if the button is held. |
Off preset |
Deprecated, leave this set to Disabled [0] |
DyNet Mute |
Stops DyNet messages being created by this function. |
Double send stop fade |
If True, 'stop fade' command is sent twice to compensate for busy networks. |
Preset
Preset
| Property | Description |
|---|---|
Preset |
Defines the preset for the button’s ON state. |
Fade (rounded to 10 ms) |
Time taken to reach the ON state. |
DyNet Mute |
Stops DyNet messages being created by this function. |
Off Preset
Instantly drops all channels in the specified area to 0% with no fade time.
| Property | Description |
|---|---|
Off Preset |
Defines the area’s OFF preset for the button’s indicator LED. |
DyNet Mute |
Stops DyNet messages being created by this function. |
Reset Preset
Resets all channels in an area to the currently selected preset, overriding any individual channel level changes that were made since the preset was selected.
| Property | Description |
|---|---|
Fade (rounded to 10 ms) |
Time taken to reset the current preset. |
DyNet Mute |
Stops DyNet messages being created by this function. |
Preset offset
| Property | Description |
|---|---|
Preset offset |
When button is pressed, all other preset commands are incremented by this amount. |
DyNet Mute |
Stops DyNet messages being created by this function. |
Preset with program
| Property | Description |
|---|---|
Preset |
If button is tapped this preset is recalled. If button is held down for three seconds, this preset is overwritten with the current channel levels. |
Fade (rounded to 10 ms) |
Time taken to reach the ON state. |
DyNet Mute |
Stops DyNet messages being created by this function. |
Increment Multi-preset
| Property | Description |
|---|---|
Start Preset |
Each button press increments the preset number up through this range, then loops back. If the current preset is out of range, the first press recalls the Start Preset. |
End Preset |
|
Fade (rounded to 10 ms) |
Time taken to fade between presets. |
DyNet Mute |
Stops DyNet messages being created by this function. |
Decrement Multi-preset
| Property | Description |
|---|---|
Start Preset |
Each button press decrements the preset number down through this range, then loops back. If the current preset is out of range, the first press will recall the Start Preset. |
End Preset |
|
Fade (rounded to 10 ms) |
Time taken to fade between presets. |
DyNet Mute |
Stops DyNet messages being created by this function. |
Ramp
Ramp up channel level
| Property | Description |
|---|---|
Fade (rounded to 10 ms) |
Time taken to ramp from the current level to 100%. |
On channels only |
If True, only channels with a level 1% or higher will ramp up. |
DyNet Mute |
Stops DyNet messages being created by this function. |
Double send stop fade |
If True, the 'stop fade' command is sent twice to ensure correct operation. |
Ramp down channel level
| Property | Description |
|---|---|
Min ramp level (%) |
Minimum light level when ramping down. |
Fade (rounded to 10 ms) |
Time taken to ramp from the current level to the Min ramp level. |
On channels only |
If True, this prevents channels currently at 0% from ramping up to the Min ramp level. |
DyNet Mute |
Stops DyNet messages being created by this function. |
Double send stop fade |
If True, the 'stop fade' command is sent twice to ensure correct operation. |
| If On channels only is set to True AND Min ramp level is set to 0%, channels ramped down to 0% are still treated as ON by this and the Ramp up channel level function. Other channels that were already at 0% are ignored. |
Ramp up colour temperature
| Property | Description |
|---|---|
Max ramp colour temperature (Kelvin) |
Sets the maximum (coolest white) colour temperature. |
Set colour temperature only |
If True, only colour temperature is affected. |
Fade (rounded to 10 ms) |
Time taken to fade from the current level to 100%. |
On channels only |
If True, only channels at level 1% or brighter are affected. |
DyNet Mute |
Stops DyNet messages being created by this function. |
Double send stop fade |
If True, the 'stop fade' command is sent twice to ensure correct operation. |
Ramp down colour temperature
| Property | Description |
|---|---|
Max ramp colour temperature (Kelvin) |
Sets the minimum (warmest white) colour temperature. |
Set colour temperature only |
If True, only colour temperature is affected. |
Min ramp level (%) |
Minimum light level when ramping down. |
Fade (rounded to 10 ms) |
Time taken to reach the Min level if the button is tapped. |
On channels only |
If True, only channels at level 1% or brighter are affected. |
DyNet Mute |
Stops DyNet messages being created by this function. |
Double send stop fade |
If True, the 'stop fade' command is sent twice to ensure correct operation. |
| If On channels only is set to True AND Min ramp level is set to 0%, channels ramped down to 0% are still treated as ON by this and the Ramp up colour temperature function. Other channels that were already at 0% are ignored. |